Fender ultimate chorus amplifier dating

Rated 3.83/5 based on 979 customer reviews

Values available include 4.7u F/50V, 10u F/500V, 22u F/50V, 22u F/500V, 47u F/500V, 80u F/450V, 100u F/100V, 100uf/350V, and 220u F/300V. Replacement for Fender Princeton and Princeton Reverb main filter capacitor on blackface and silverface amps from the 1960s and 1970s. Perfect for amplifier circuit additions or modifications. Each lug will accept wires up to 16ga - smaller gauge allows multiple wires to be connected to each lug. Introduced on Blonde, Brown, and Blackface-era Fender amplifiers. Introduced on some Blonde and Brownface-era Fender amplifiers. Used on the upper left corner of the grill cloth on most blackface era Fender amps. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall.Also may be used for Fender Champ, Vibro-Champ and Bronco amps from the same era (one extra 20u F section unused on these amps. OUTSIDE EDGE OF WASHER IS BARELY LARGER THAN THE HEAD OF THE Fender BACK PANEL SCREWS. OD 7/16", ID 3/16" Typically found on the back panel of some Fender Blackface/Silverface vintage amps and the reissues of those amps. OD 7/16", ID 3/16" Typically found on the back panel of some Fender Blackface/Silverface vintage amps and the reissues of those amps. End terminals on each strip are the mounting lugs, so they become a ground lug if attached to a metal chassis. Used on '65 Twin Reverb, '65 Deluxe Reverb, '65 Super Reverb, '65 Princeton Reverb, '64 Vibroverb Custom, Custom Vibrolux, Vibro-King 212 Enclosure, Blues Junior, Pro Junior, Acoustasonic Jr. Original Fender part number 0994093000Fender AMP LOGO.Rated 85 degrees C, -10%/ 50% number 125C3A & 022707. Vacuum impregnated with polyurethane varnish for quiet and long life operation. Typically found on the back panel of some Fender Blonde/Brown era amps, and some Blackface vintage amps. Larger than the CW-401-4 - Fender was not consistent in which washers they used on back panels over the years. Larger than the CW-401-4 / CW-401-8 sets - Fender was not consistent in which washers they used on back panels over the years. Ground Connection Terminals - Flat Used to connect a ground wire to a screw and nut on a chassis. With built-in lock washer to keep the screw and nut from loosening. DSP, Acoustasonic 30, Acoustasonic SFX II, Bassman 25, Bassman 60, Jazzmaster Ultralight Enclosure, Princeton 650, Cyber Champ, Rumble 112, Rumble 2x8, Super-Sonic 100 Head, Super-Sonic Twin, Super Champ X2/XD, and Bullet 15 DSP amplifier. New original Fender reproduction, for the CBS era (1970s).For dimensions and technical specifications, click number 125C1A & 022699. Vacuum impregnated with polyurethane varnish for quiet and long life operation. OUTSIDE EDGE OF WASHER IS BARELY LARGER THAN THE HEAD OF THE Fender BACK PANEL SCREWS. "Tailless" Fender logo, cast metal, mounting screws included.

Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, etc. CAPACITOR, F&T BRAND, AXIAL LEAD ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Made in Germany.

Screw spacing is 5 inches center-to-center, strap length is 5 5/8" end-to-end. Screw spacing is 4 inches center-to-center, strap length is 4 5/8" end-to-end.

Fender Chassis Strap - Nickel-Plated - Large (5") for Twin, Bassman, Super, Showman, Vibro-King, Pro, Pro Reverb, Prosonic, etc. Screw spacing is 5 inches center-to-center, strap length is 5 5/8" end-to-end. Fender Chassis Strap - Black - Large (5") for Twin, Bassman, Super, Showman, Vibro-King, Pro, Pro Reverb, Prosonic, etc. Screw spacing is 5 inches center-to-center, strap length is 5 5/8" end-to-end. Fender Chassis Straps w/ hardware - Medium (4") For Deluxe, Vibrolux, etc. Fender Chassis Straps with hardware - Medium (4") for later silverface versions of the medium-size Fender Amps: Deluxe Reverb, Vibrolux Reverb, etc. Bolts screw into a captive nut on the top rail of the chassis, so there are no bottom nuts on these models.

For dimensions and technical specifications, click here. For vintage blackface and silverface Twin Reverb, Pro Reverb, Super Reverb, Vibrolux Reverb, etc. 10" cut leads, X-Mount with 1 3/4" mounting centers. Typically found on the back panel of some Fender Blonde/Brown era amps, and some Blackface vintage amps. Does NOT contain the "Made in USA" script found on some Fender logos. New original Fender reproduction, used in many recent and current model Fenders.

Input impedance 14.5K ohms, output impedance 4 ohms. Used on the upper left corner of the grill cloth on most CBS era Fender amps. 4 1/2" wide, the "F" in the logo is about 2 1/2" inches tall. "Flat" Fender logo, with black "tail", cast metal, mounting screws included. New original Fender reproduction, used in many recent and current model Fenders.

Leave a Reply